![Hitachi CS51EA [13/112] English](/img/pdf.png)
Hitachi CS51EA [13/112] English
![Hitachi CS51EA [13/112] English](/views2/1081739/page13/bgd.png)
13
English
Icing protection system (Fig. 39, 40)
This system is to protect carburetor from icing when the unit is
operated in winter time.
1. When you need icing system work, remove air fi lter cover (41).
Pull out the shutter (45) from inside the air fi lter cover and
reinstall it in winter time position by turning half-way. (Fig. 39)
This will allow heated air to fl ow from cylinder side to carburetor
cabin through the opening (46).
NOTE
When winter time has been over and carburetor will not suff er from
icing, make sure that the shutter is reinstalled in ordinary position
(Fig. 40).
For long-term storage
Drain all fuel from the fuel tank. Start and let engine run until it stops.
Repair any damage which has resulted from use. Clean the unit with
a clean rag, or the use of high pressure air hose. Put a few drops of
two-cycle engine oil into the cylinder through the spark plug hole,
and spin the engine over several times to distribute oil.
Cover the unit and store it in a dry area.
CHAIN SHARPENING
Parts of a cutter (Fig. 41, 42)
WARNING
○ Gloves should be used when sharpening chain.
○ Be sure to round off the front edge to reduce the chance of
kickback or tie-strap breakage.
47. Top plate
48. Cutting corner
49. Side plate
50. Gullet
51. Heel
52. Chassis
53. Rivet hole
54. Toe
55. Depth gauge
56. Correct angle on top plate (degree of angle depends on chain
type)
57. Slightly protruding “hook” or point (curve on non-chisel chain)
58. Top of depth gauge at correct height below top plate
59. Front of depth gauge rounded off
LOWERING DEPTH GAUGES WITH A FILE
1) If you sharpen your cutters with a fi le holder, check and lower the
depth.
2) Check depth gauges every third sharpening.
3) Place depth gauge tool on cutter. If depth gauge projects, fi le
it level with the top of the tool. Always fi le from the inside of the
chain toward an outside cutter. (Fig. 43)
4) Round off front corner to maintain original shape of depth gauge
after using depth gauge tool. Always follow the recommended
depth gauge setting found in the maintenance or operator
manual for your saw. (Fig. 44)
GENERAL INSTRUCTIONS FOR FILING CUTTERS
File (60) cutter on one side of the chain from the inside out. File on
forward stroke only. (Fig. 45)
5) Keep all cutters the same length. (Fig. 46)
6) File enough to remove any damage to cutting edges (side plate
(62) and top plate (63)) of cutter. (Fig. 47)
NOTE
Do not fi le or alter the tops of bumper drive links (61). (Fig. 46)
SHARPENING ANGLES FOR SHARPENING SAW CHAIN
1. Part Number 95VPX/20BPX
2. Pitch 0.325”
3. Depth Gauge Setting 0.025"
85°
4. Side Plate Filing Angle 85°
5. Top Plate Angle 30°
100°
6. File Guide Angle 100°
Maintenance schedule
Below you will fi nd some general maintenance instructions. For
further information please contact Hitachi Authorized Service
Centers.
Daily maintenance
○ Clean the exterior of the unit.
○ Clean the chain oil fi lter port.
○ Clean the groove and oil fi lter port in the guide bar.
○ Clean the side case of saw dust.
○ Check that the saw chain is sharp.
○ Check that the bar nuts are suffi ciently tightened.
○ Make sure that the chain transport guard is undamaged and that
it can be securely fi tted.
○ Check that nuts and screws are suffi ciently tightened.
Especially inspect the bolt of muffl er and ensure that they are
properly tightened before starting engine. Should any of the
bolts be loose, retighten them immediately. Failure to do so
could result in serious hazard.
○ Check the tip of the guide bar. Please exchange it for the new
one when it is worn out.
○ Check the band of chain brake. Please exchange it for the new
one when it is worn out.
○ Clean the air fi lter.
Weekly maintenance
○ Check the recoil starter, especially cord.
○ Clean the exterior of the spark plug.
○ Remove the spark plug and check the electrode gap. Adjust it to
0.6 mm or change the spark plug.
○ Clean the cooling fi ns on the cylinder and check that the air
intake at the recoil starter is not clogged.
Monthly maintenance
○ Rinse the fuel tank with gasoline, and clean fuel fi lter.
○ Clean chain oil fi lter.
○ Clean the exterior of the carburetor and the space around it.
○ Clean the fan and the space around it.
NOTE
When ordering the parts to your nearest dealer, please use the
item numbers showing on the parts breakdown section in this
instruction.
BAR NO. LENGTH-TYPE CHAIN NO.
MODEL NO.
OREGON
160MLBK041
180MLBK041
200PXBK041
16”
18”
20”
95VPX-66
95VPX-72
20BPX-78
000Book_CS51EAP_EE.indb 13000Book_CS51EAP_EE.indb 13 2012/03/19 12:15:492012/03/19 12:15:49
Содержание
- Cs 51eap cs 51ea 1
- English 6
- Meanings of symbols 6
- Original instructions 6
- English 7
- What is what 7
- English 8
- Warnings and safety instructions 8
- English 9
- Specifications 9
- Assembly procedures 10
- English 10
- Operating procedures 10
- English 11
- English 12
- Maintenance 12
- English 13
- Bedeutungen der symbole 14
- Deutsch 14
- Übersetzung der original gebrauchsanweisung 14
- Deutsch 15
- Teilebezeichnungen 15
- Deutsch 16
- Warn und sicherheitshinweise 16
- Deutsch 17
- Deutsch 18
- Technische daten 18
- Zusammenbau 18
- Betrieb 19
- Deutsch 19
- Deutsch 20
- Deutsch 21
- Wartung 21
- Deutsch 22
- Deutsch 23
- Ελληνικά 24
- Επεξηγηση συμβoλων 24
- Μετάφραση των αρχικών οδηγιών 24
- Tι ειναι τι 25
- Ελληνικά 25
- Ελληνικά 26
- Προειδοποιησεισ και υποδειξεισ ασφαλειασ 26
- Ελληνικά 27
- Διαδικασιεσ συναρμολογησησ 28
- Ελληνικά 28
- Τεχνικα χαρακτηριστικα 28
- Διαδικασια λειτουργιασ 29
- Ελληνικά 29
- Ελληνικά 30
- Ελληνικά 31
- Συντηρηση 31
- Ελληνικά 32
- Ελληνικά 33
- Polski 34
- Tłumaczenie oryginalnych instrukcji 34
- Znaczenie symboli 34
- Polski 35
- Zasadnicze podzespoły urządzenia 35
- Ostrzeżenie i instrukcje bezpieczeństwa 36
- Polski 36
- Polski 37
- Polski 38
- Procedury montażu 38
- Specyfikacje 38
- Polski 39
- Procedury obsługi 39
- Polski 40
- Konserwacja 41
- Polski 41
- Polski 42
- Polski 43
- Fordítás az eredeti útmutatót 44
- Magyar 44
- Szimbólumok jelentései 44
- Magyar 45
- Mi micsoda 45
- Figyelmeztetések és biztonsági óvintézkedések 46
- Magyar 46
- Magyar 47
- Magyar 48
- Technikai adatok 48
- Összeszerelési eljárások 48
- Magyar 49
- Működtetési eljárások 49
- Magyar 50
- Karbantartás 51
- Magyar 51
- Magyar 52
- Překlad původních pokynů 53
- Význam symbolů 53
- Čeština 53
- Co je co 54
- Čeština 54
- Varování a bezpečnostní pokyny 55
- Čeština 55
- Specifikace 56
- Čeština 56
- Montážní postupy 57
- Obsluha 57
- Čeština 57
- Čeština 58
- Údržba 59
- Čeština 59
- Čeština 60
- Asıl talimatların çevirisi 61
- Sembollerin anlamlari 61
- Türkçe 61
- Tanimlar 62
- Türkçe 62
- Türkçe 63
- Uyarilar ve güvenli k tali matlari 63
- Türkçe 64
- Montaj i şlemleri 65
- Spesi fi kasyonlar 65
- Türkçe 65
- Türkçe 66
- Çaliştirma 66
- Türkçe 67
- Türkçe 68
- Türkçe 69
- Română 70
- Semnificaţia simbolurilor 70
- Traducerea instrucţiunilor originale 70
- Ce şi ce este 71
- Română 71
- Avertismente şi instrucţiuni de siguranţă 72
- Română 72
- Română 73
- Proceduri de asamblare 74
- Română 74
- Specificatii 74
- Proceduri de operare 75
- Română 75
- Română 76
- Mentenanţă 77
- Română 77
- Română 78
- Pomen simbolov 79
- Prevod originalnih navodil 79
- Slovenščina 79
- Opis sestavnih delov 80
- Opozorila in varnostna navodila 80
- Slovenščina 80
- Slovenščina 81
- Slovenščina 82
- Specifikacije 82
- Postopek montaže 83
- Postopek upravljanja 83
- Slovenščina 83
- Slovenščina 84
- Slovenščina 85
- Vzdrževanje 85
- Slovenščina 86
- Preklad pôvodných pokynov 87
- Slovenčina 87
- Význam symbolov 87
- Slovenčina 88
- Čo je čo 88
- Slovenčina 89
- Výstrahy a bezpečnostné pokyny 89
- Slovenčina 90
- Postupy montáže 91
- Slovenčina 91
- Špecifikácie 91
- Prevádzkové postupy 92
- Slovenčina 92
- Slovenčina 93
- Slovenčina 94
- Údržba 94
- Slovenčina 95
- Значение символов или табличек 96
- Перевод оригинальных инструкций 96
- Русский 96
- Русский 97
- Что это такое 97
- Предостережения и инструкции по технике безопасности 98
- Русский 98
- Русский 99
- Русский 100
- Сборочные операции 100
- Спецификации 100
- Рабочие операции 101
- Русский 101
- Русский 102
- Русский 103
- Техобслуживание 103
- Русский 104
- Русский 105
- Cs51eap 106
- Cs51eap 107
- Cs51ea 108
- Cs51ea 109
- Book_cs51eap_ee indb 111 000book_cs51eap_ee indb 111 2012 03 19 12 16 36 2012 03 19 12 16 36 111
- Clonshaugh business technology park dublin 17 lreland 111
- Deklaracja zgodności z eci 111
- Deutsch 111
- Ec declaration of conformity 111
- Ek megfelelőségi nyilatkozat 111
- English 111
- Erklärung zur konformität mit ce regeln 111
- F tashimo vice president director 111
- Head offi ce in japan 111
- Hitachi koki co ltd 111
- Hitachi koki europe ltd 111
- Hitachi power tools europe gmbh 111
- Magyar 111
- Polski 111
- Prohlášení o shodě s ec 111
- Representative offi ce in europe 111
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 111
- Siemensring 34 47877 willich 1 f r germany 111
- Technical fi le at 111
- Čeština 111
- Εκ δηλωση εναρμ νισμ υ 111
- Ελληνικά 111
- Ab uygunluk beyani 112
- Book_cs51eap_ee indb 112 000book_cs51eap_ee indb 112 2012 03 19 12 16 45 2012 03 19 12 16 45 112
- Clonshaugh business technology park dublin 17 lreland 112
- Code no e99245592 na printed in china 112
- Declaraţie de conformitate ce 112
- Ec deklaracija o skladnosti 112
- F tashimo vice president director 112
- Head offi ce in japan 112
- Hitachi koki co ltd 112
- Hitachi koki europe ltd 112
- Hitachi power tools europe gmbh 112
- Pyсский 112
- Representative offi ce in europe 112
- Română 112
- Sadece avrupa ülkeleri için geçerlidir orman hizmeti için portatif elektrikli testere cs51eap cs51ea 112
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 112
- Siemensring 34 47877 willich 1 f r germany 112
- Slovenčina 112
- Slovenščina 112
- Technical fi le at 112
- Türkçe 112
- Valabil numai pentru europa fierăstrău portabil cu lanţ pentru servicii forestiere cs51eap cs51ea 112
- Velja le za evropo prenosna verižna žaga za gozdno službo cs51eap cs51ea 112
- Vyhlásenie o zhode ec 112
- Vzťahuje sa len na krajiny európy prenosná reťazová píla na lesnícke účely cs51eap cs51ea 112
- Декларация соответствия ес 112
- Только для европы портативная цепная пила для лесных работ cs51eap cs51ea 112
Похожие устройства
- Mitsubishi Electric PKH-3FKA-E Инструкция по эксплуатации
- Sony SVT-1112S1R/S Silver Инструкция по эксплуатации
- Hitachi CS33EDT Инструкция по эксплуатации
- Mitsubishi Electric PKH-3FAKH Инструкция по эксплуатации
- Dell Inspiron 3520 /3520-5917/ Инструкция по эксплуатации
- Hitachi CS45EM Инструкция по эксплуатации
- Mitsubishi Electric PKH-2.5FKHA3 Инструкция по эксплуатации
- HP Spectre XT 13-2000er B3Y76EA Инструкция по эксплуатации
- Mitsubishi Electric PKH-2.5FKHA2 Инструкция по эксплуатации
- Nord ПГ4 103-4А Инструкция по эксплуатации
- Packard Bell Easynote LV11HC-33114G50Mnks Инструкция по эксплуатации
- Mitsubishi Electric PKH-2.5FKHA1 Инструкция по эксплуатации
- Nord ПГ4 205-7А Инструкция по эксплуатации
- Acer Aspire One 756-B8478kk Инструкция по эксплуатации
- Mitsubishi Electric PKH-2.5FKA3 Инструкция по эксплуатации
- Nord ПГ4 205-1А Инструкция по эксплуатации
- Asus X55A 90NBHA138W2A14OC43AU SX044O Инструкция по эксплуатации
- Mitsubishi Electric PKH-2.5FKA2 Инструкция по эксплуатации
- Nord ПГ4 204-7А Инструкция по эксплуатации
- HP TouchSmart 520-1209er B9S12EA Инструкция по эксплуатации
Скачать
Случайные обсуждения