![GRAPHITE 59G209 [13/96] Operation and maintenance](/img/pdf.png)
GRAPHITE 59G209 [13/96] Operation and maintenance
![GRAPHITE 59G209 [13/96] Operation and maintenance](/views2/2041631/page13/bgd.png)
13
• Never strike the workpiece with a working tool.
• Do not use the grinding wheel for hammering or stripping of the
workpiece, especially when corners, sharp edges are worked, etc.
(this may cause loss of control of the power tool and recoil).
• Do not use discs from circular saws intended for wood cutting.
Failure to observe this recommendation may result in recoil of
the power tool, loss of control and may lead to injuries of the
operator.
SWITCHING ON /SWITCHING OFF
When the grinder is switched on and operated, it should be held with
both hands. The grinder is equipped with the switch protecting against
accidental activation.
• Move the lever switch (7) forward.
• Press the switch button (2) (g. C).
• When the switch button (2) is released, the grinder stops.
Motor starts operation with soft-start, which is used for starting the
motor without load.
Once the grinder is switched on, wait until the grinding wheel
reaches maximum speed and only then you can begin to work.
During operation do not use the switch to switch the grinder on
and o. The grinder switch can be used only when the power tool is
moved away from the workpiece.
CUTTING
• The angle grinder can be used for cutting in a straight line only.
• Do not cut a workpiece holding it in your hands.
• Large workpiece should be supported. Make sure the support
points are located near the cutting line and at the ends of the
workpiece. A stably located workpiece will not tend to move,
when it is cut.
• Small workpieces should be fastened in a vice or using clamps, for
example. The workpiece should be fastened so that it is cut near
the fastening element. This will ensure higher cutting precision.
• Do not allow the cut-o wheel to vibrate or jump, since this will
lower the quality of cutting and may cause the cut-o wheel to
break.
• Do not exert lateral pressure onto the cut-o wheel during
cutting.
• A proper cut-o wheel should be used depending on a workpiece
type.
• When a workpiece is cut, it is recommended that a cutting
direction is the same as rotation direction of the cut-o wheel.
The cutting depth depends on a wheel diameter (g. G).
• Only wheels with nominal diameters not larger than recommended
for a given grinder model should be used.
• Do not allow the fastening anges to contact a workpiece in case of
deep cuts (e.g. sections, building blocks, bricks, etc.).
Cut-o wheels reach high temperatures during operation. It cannot
be touched with uncovered body parts, before they cool down.
GRINDING
Grinding wheel, cup-type grinding wheels, ap wheels, wheels with
abrasive bre, wire brushes and exible discs, etc. should be used for
grinding. Each type of discs and workpiece requires proper working
method and personal protective equipment.
Cut-o wheels should not be used for grinding.
Grinding discs are intended for removal of material with an edge of
the disc.
• Do not use the lateral surface for grinding. The optimum working
angle for this disc type is 30° (g. H).
• Works related to grinding can be performed only, when proper
grinding discs are used for a given workpiece.
When ap wheels, discs with abrasive bre and exible discs for
sandpaper are used, attention should be paid to the proper tool
angle (g. I).
• Do not grind with the entire surface of a wheel.
• This disc type should be used for working at surfaces.
Wire brushes are mainly used for cleaning sections and hard-to-reach
spaces. They can be used to remove rust, painting coats, etc. from a
workpiece surface (g. K).
Only such working tools can be used, whose permissible rotational
speed is higher or equal to the maximum no load speed of the
grinder.
OPERATION AND MAINTENANCE
Before any operations related to installation, adjustment, repairs or
maintenance are commenced, the plug of the power cord should be
disconnected from the socket.
MAINTENANCE AND STORAGE
• It is recommended to clean the tool after each use.
• Do not use water or other uids for cleaning.
• The tool should be cleaned with a dry piece of cloth or blown with
compressed air of low pressure.
• Do not use any cleaning agents or solvents, since they may damage
plastic parts.
• Venting slots in the motor housing should be cleaned on a regular
basis not to overload the tool.
• When the power cord is damaged, it should be replaced with the
power cord of the same parameters. It should be performed by a
qualied professional or the tool should be delivered to an authorised
service shop.
• When the commutator sparks excessively, have the condition of
motor carbon brushes checked by a qualied person.
• The tool should be always stored in a dry place and out of reach of
children.
REPLACING THE CARBON BRUSHES
Immediately replace worn out (shorter than 5 mm), burnt or cracked
motor carbon brushes. Always replace both carbon brushes at a time.
• Unscrew and remove carbon brush covers (7) (g. E).
• Pull the pressure spring away, snap out and remove worn out carbon
brushes.
• Remove any carbon dust with compressed air.
• Install new carbon brushes (they should easily slide into the brush
holders) and reinstall the pressure spring (g. F).
• Fix carbon brush covers (7).
After the carbon brushes are replaced, switch on the grinder with
no load and wait for 1-2 minutes to make the carbon brushes t
the motor commutator. Carbon brushes should be replaced by a
qualied person using original spare parts only.
All types of faults and defects should be eliminated by an authorised
service of the manufacturer.
SPECIFICATIONS
RATED DATA
Angle Grinder 59G209
Parameter Value
Power supply voltage 230 V AC
Power supply frequency 50 Hz
Rated power 2900 W
Rated rotational speed 6500 min
-1
Max. grinding wheel diameter 230 mm
Inner disc diameter 22,2 mm
Spindle thread M14
Protection class II
Weight 5,9 kg
Year of manufacture 2021
59G209 defines type and indication of the device
NOISE LEVEL AND VIBRATION PARAMETERS
Acoustic pressure level L
pA
= 95,7 dB (A) K=3dB (A)
Acoustic power level L
WA
= 106,7 dB (A) K=3dB (A)
Vibration acceleration value (rear handle): a
h
= 5,355 m/s
2
K=1,5 m/s
2
Vibration acceleration value (front handle): a
h
= 5,165 m/s
2
K=1,5 m/s
2
Noise and vibration information
Noise produced by the device is dened with: level of produced sound
pressure L
pA
and level of sound power L
WA
(where K is measurement
uncertainty). Vibrations produced by the device are dened with
vibration acceleration value a
h
(where K is measurement uncertainty).
Sound pressure L
pA
, sound power L
WA
and vibration acceleration a
h
Содержание
- Instrukcja oryginalna obsługi szlifierka kątowa 59g209 6
- Szczegółowe przepisy bezpieczeństwa 6
- 2 3 4 5 7
- Praca ustawienia 8
- Przygotowanie do pracy 8
- Obsługa i konserwacja 9
- Parametry techniczne 9
- Detailed safety regulations 10
- Gwarancja i serwis 10
- Ochrona środowiska 10
- Translation of the original instructions angle grinder 59g209 10
- 2 3 4 5 12
- Operation adjustments 12
- Preparation for work 12
- Operation and maintenance 13
- Specifications 13
- Detaillierte sicherheitsvorschriften 14
- Environmental protection 14
- Übersetzung der originalbetriebsanleitung winkelschleifer 59g209 14
- 2 3 4 5 16
- Vorbereitung auf den einsatz 16
- Bedienung und wartung 17
- Betrieb einstellungen 17
- Technische parameter 18
- Umweltschutz 18
- Перевод оригинальной инструкции машина шлифовальная угловая 59g209 18
- Частные требования по безопасности 18
- 2 3 4 5 20
- Подготовка к работе 21
- Работа настройка 21
- Технические характеристики 22
- Техническое обслуживание 22
- Защита окружающей среды 23
- Информация о дате изготовления 23
- Находится на изделии 23
- Переклад інструкції з оригіналу машина шліфувальна кутова болгарка 59g209 23
- Під час користування устаткуванням 23
- Спеціальні правила техніки безпеки 23
- Указана в серийном номере который 23
- 2 3 4 5 25
- Підготовка до роботи 25
- Порядок роботи робочі налаштування 26
- Зберігання та обслуговування 27
- Охорона середовища 27
- Технічні характеристики 27
- Eredeti használati utasítás fordítása sarokcsiszoló 59g209 28
- Részletes biztonsági előírások 28
- 2 3 4 5 29
- Felkészítés az üzembehelyezésre 30
- Munkavégzés beállítások 30
- Kezelése és karbantartása 31
- Környezetvédelem 31
- Műszaki jellemzők 31
- Reguli de siguranță detaliate 32
- Traducere a instrucțiunilor originale polizor unghiular 59g209 32
- 2 3 4 5 33
- Lucrul asamblarea 34
- Pregătirea pentru lucru 34
- Deservirea întreţinerea 35
- Parametrii tehnici 35
- Protecţia mediului 35
- Podrobné bezpečnostní pokyny 36
- Překlad původního návodu k používání úhlová bruska 59g209 36
- 2 3 4 5 37
- Provoz nastavení 38
- Příprava k práci 38
- Detailné bezpečnostné predpisy 39
- Ochrana životního prostředí 39
- Preklad pôvodného návodu na použitie uhlová brúska 59g209 39
- Péče a údržba 39
- Technické parametry 39
- 2 3 4 5 41
- Pred uvedením do prevádzky 41
- Ošetrovanie a údržba 42
- Práca nastavenia 42
- Ochrana životného prostredia 43
- Prevod izvirnih navodil kotni brusilnik 59g209 43
- Specifični varnostni predpisi 43
- Technické parametre 43
- 2 3 4 5 45
- Priprava na uporabo 45
- Tehnični parametri 46
- Uporaba nastavitve 46
- Vzdrževanje in hramba 46
- Detalios darbo saugos taisyklės 47
- Originalios instrukcijos vertimas kampinis šlifuoklis 59g209 47
- Varovanje okolja 47
- 2 3 4 5 48
- Darbas ir reguliavimas 49
- Pasiruošimas darbui 49
- Aplinkos apsauga 50
- Aptarnavimas ir priežiūra 50
- Techniniai duomenys 50
- Instrukciju tulkojums no oriģinālvalodas leņķa slīpmašīna 59g209 51
- Speciālie drošības noteikumi 51
- 2 3 4 5 52
- Darbs iestatījumi 53
- Sagatavošanās darbam 53
- Algupärase kasutusjuhendi tõlge nurklihvija 59g209 54
- Apkalpošana un apkope 54
- Eriohutusjuhised 54
- Tehniskie parametri 54
- Vides aizsardzība 54
- 2 3 4 5 56
- Ettevalmistus tööks 56
- Hooldus ja hoidmine 57
- Tehnilised parameetrid 57
- Töö seadistamine 57
- Keskkonnakaitse 58
- Подробни правила за безопасност 58
- Превод на оригиналната инструкция ъглова шлайфмашина 59g209 58
- 2 3 4 5 60
- Подготовка за работа 60
- Работа настройки 61
- Обслужване и поддръжка 62
- Опазване на околната среда 62
- Технически параметри 62
- Posebni propisi o sigurnosti 63
- Prijevod originalnih uputa kutna brusilica 59g209 63
- 2 3 4 5 64
- Priprema za rad 65
- Rad postavke 65
- Rukovanje i održavanje 65
- Opšte mere bezbednosti 66
- Prevod orginalnog uputstva ugaona brusilica 59g209 66
- Tehnički parametri 66
- Zaštita okoliša 66
- 2 3 4 5 68
- Priprema za rad 68
- Korišćenje i održavanje 69
- Rad postavke 69
- Tehničke karakteristike 70
- Zaštita sredine 70
- Ειδικεσ απαιτησεισ ασφαλειασ 70
- Μετάφράση του πρωτοτυπου των οδηγιων χρησησ γωνιάκο τριβειο 59g209 70
- 2 3 4 5 72
- Λειτόυργια ρυθμιση 73
- Πρόετόιμασια για εργασια 73
- Τεχνικα χαρακτηριστικα 74
- Τεχνικη συντηρηση 74
- Normas de seguridad detalladas 75
- Traducción del manual original amoladora angular 59g209 75
- Πρόστασια περιβαλλόντόσ 75
- 2 3 4 5 76
- Preparación para trabajar 77
- Trabajo ajustes 77
- Parametros técnicos 78
- Uso y mantenimiento 78
- Norme particolari di sicurezza 79
- Protección medioambiental 79
- Traduzione delle istruzioni originali smerigliatrice angolare 59g209 79
- 2 3 4 5 81
- Preparazione al funzionamento 81
- Funzionamento regolazione 82
- Servizio e manutenzione 82
- Gedetailleerde 83
- Parametri tecnici 83
- Protezione dell ambiente 83
- Veiligheidsvoorschriften 83
- Vertaling van de originele handleiding van de haakse slijper 59g209 83
- 2 3 4 5 85
- Werkvoorbereiding 85
- Bediening en onderhoud 86
- Werk instellingen 86
- Milieubescherming 87
- Règles de sécurité détaillées 87
- Technische parameters 87
- Traduction de la notice d emploi originale meuleuse d angle 59g209 87
- 2 3 4 5 89
- Preparation au travail 90
- Travail réglages 90
- Entretien et conservation 91
- Paramètres techniques 91
- Protection de l environnement 91
- Deklaracja zgodności we 92
- Ec declaration of conformity megfelelőségi nyilatkozat ek es vyhlásenie o zhode prohlášení o shodě es ео декларация за съответствие declarația de conformitate ce eg konformitätserklärung dichiarazione di conformità ce 92
Похожие устройства
- GRAPHITE 59G175 Инструкция по эксплуатации
- GRAPHITE 59G187 Инструкция по эксплуатации
- GRAPHITE 59G348 Инструкция по эксплуатации
- GRAPHITE 59G088 Инструкция по эксплуатации
- BQ MG1010 Инструкция по эксплуатации
- BQ MG1009 Инструкция по эксплуатации
- BQ MG1007 Инструкция по эксплуатации
- BQ MG2004 Инструкция по эксплуатации
- BQ MG2005 Инструкция по эксплуатации
- BQ MG2003 Инструкция по эксплуатации
- BQ MG2002 Инструкция по эксплуатации
- BQ MG2000 Инструкция по эксплуатации
- BQ MG2001 Инструкция по эксплуатации
- BQ J1006 Инструкция по эксплуатации
- BQ J1007 Инструкция по эксплуатации
- BQ J3000 Инструкция по эксплуатации
- BQ J2002 Инструкция по эксплуатации
- BQ J2001 Инструкция по эксплуатации
- BQ SB1009 Инструкция по эксплуатации
- BQ HB1031SS Инструкция по эксплуатации